A. Radiated Immunity test for 10m and MIL/Automotive chambers
1. Signal Generators and RF Switching units
1.1 Signal Generator(9kHz~6GHz)
1.2 Signal Generator(100kHz~40GHz)
1.3 RF Switching unit(9KHz~6GHz)
1.4 RF Switching unit(DC & 18GHz)
2. RF Power Amplifiers and High Power Switching unit
2.1 RF Power Amplifier(10kHz~225MHz)
2.2 RF Power Amplifier(80MHz~1GHz)
2.3 RF Power Amplifier(800MHz~6GHz)
2.4 RF Power Amplifier(6GHz~18GHz)
2.5 High Power Switching unit(10KHz~1GHz)
2.6 Termination load(DC & 18GHz)
3. Immunity Antennas
3.1 E-H Field Generator(10kHz~100MHz)
3.2 Biconical Antenna(20MHz~220MHz)
3.3 Log Periodic Antenna(80MHz~1GHz)
3.4 Horn Antenna(800MHz~6GHz)
3.5 Horn Antenna(6GHz~18GHz)
4. Power Monitoring set
4.1 Power meter (2 set)
4.2 Power sensors
(1) Power Sensor(2 ea, 50MHz~18GHz)
- SWR : 50MHz~2.4GHz(<1.16), 2.4GHz~8GHz(<1.20)
(2) Power Sensor(2 ea, 9kHz~6GHz)
- SWR : 9kHz~2.4GHz(<1.13), 2.4GHz~6GHz(<1.20)
5. Field Monitoring and RF switching set
5.1 Field monitor(5kHz~60GHz, probe dependent)
5.2 Laser Field probe(1.5~300V/m)
5.3 Laser Field probe(2~300V/m)
5.4 Field Probe stand
7. Add on items for IEC61000-4-3
7.1 Log periodic antenna(700MHz~9GHz)
8. Add on items for MIL461E/F RS101
8.1 Waveform Generator(10µHz~20MHz)
8.2 Audio Amplifier(DC & 300kHz)
8.3 Radiating loop(D=12cm), Loop sensor(D=4cm)
8.4 Precision resistor(2.2Ohm), Current Probe, Cable and Adapter
B. Conducted Immunity test
1. Conducted Immunity for IEC/EN61000-4-6
1.1 RF Power Amplifier and coupler(10kHz~400MHz)
1.2 Signal Generator(10kHz~1GHz)
1.3 Power meter
1.4 Power Sensor(3 ea, 9kHz~6GHz)
1.5 CDNs for IEC/EN61000-4-6, EM Clamp set
2. Add on items for MIL461E/F CS101
2.1 Coupling Transformer
2.2 Isolation Transformer(15Hz~150kHz)
2.3 10μF Feedthrough Capacitor
3. Add on Items for MIL461E/F CS106
3.1 Transient generator(1.5±0.5µs into 5Ω)
4. Add on items for MIL461E/F CS114
4.1 Current Injection Probe(10kHz~400MHz)
4.2 Current Probe(10kHz~500MHz)
5. Add on items for MIL461E/F CS115
5.1 Pulse generator(0~2,000V)
5.2 Injection Probe(2MHz~450MHz)
5.3 Current probe(10kHz~500MHz)
6. Add on items for MIL461E/F CS116
6.1 Damped sinusoidal transient generator(10, 100kHz, 1, 10, 30, 100MHz Selectable)
6.2 Multiple impedance coupling device
- 1:1.5 voltage step-up or current step-down
- 2:1.0 voltage step-down or current step-up
- 1:3.0 voltage step-up or current step-down
7. Add on items for Automotive Pulse System
7.1 Compact Automotive generator
7.2 Compact Load Dump Simulator
7.3 Bi Polar Voltage Drop Simulator(-15V~+60V/50A continuous, 150A inrush current up to 200ms)
7.4 Power Fail simulator, On-Board Wave Generator, DC source 16V/10A
7.5 ISO Software License, Control software, Generate the Pulse Superimposed Voltage profile)
7.6 System RACK and controller, Coupling clamp, Calibration resistor kit for plus as ISO7637-2
7.7 Electric Switch for transient emission test(Max. 60V DC, Max. 100A continuous)
7.8 Mechanical Switch for transient emission test(Max. 16V DC, Max. 40A DC continuous)
7.9 Artificial Network(DC LISN, ISO 7637-2, Max 400A for 10ms)
7.10 Calibration load electronic switch
8. Equipment for IEC/EN61000-4-4/5/11/34 : 1 set
8.1 EFT(4.4 kV), Burst(1MHz) and Surge Simulator
- Surge IEC 61000‐4‐5 Ed.3
- CWG 1.2/50μs(4.1kV), 8/20μs(2.05kA)
- Interruption up to 16A IEC 61000‐4‐11